Oldcastle Kitchen Remodeling in Las Vegas, NV

Oldcastle Kitchen Remodeling: The Las Vegas Owner’s Guide

Oldcastle kitchen remodeling in Las Vegas typically runs $14,000-$45,000 for a full project, and we stock Oldcastle-compatible materials for same-week starts on most jobs. Most Las Vegas homeowners discover their Oldcastle cabinets, countertops, or hardware are failing when doors stop soft-closing, drawer glides stick in the dry heat, or laminate surfaces bubble near the sink after years of hard water exposure.

Call (855) 951-4361

Which Oldcastle Models This Applies To

Oldcastle manufactures under several kitchen product lines, and matching the right replacement matters. Look for the foil label inside the cabinet door frame or stamped on the drawer box edge. The most common Las Vegas installations we service are from the Oldcastle Kitchen Solutions series (2012-2019), the Premium Cabinet line with soft-close hinge packs, and the Builder Select economy grade found in many Summerlin and Henderson tract homes from the mid-2000s.

The hinge bore pattern on Oldcastle doors is 35mm, but the cup depth varies between 11.5mm (Solutions) and 13mm (Premium). Mix these up and your door won’t seat flush. For drawer glides, Oldcastle used both 22-inch side-mount ball-bearing sets and 21-inch undermount soft-close rails depending on the year. The undermounts require precise 37mm from cabinet face to glide centerline. We carry both OEM Oldcastle hardware and Blum aftermarket equivalents that fit the same bore patterns. The Blum clips last longer in our experience, but if you’re matching existing finishes exactly, OEM keeps the color consistent. We are an independent service provider, not affiliated with Oldcastle.

Signs Your Oldcastle Kitchen Remodeling Is Failing

• Doors slam or won’t stay closed. The Oldcastle soft-close hinge cylinder has lost its hydraulic fluid, common after 6-8 years in Las Vegas heat. The plastic bushing inside cracks first, then the oil weeps out through the pin.
• Drawers stick, tilt, or fall off the track. The undermount glide bracket screws work loose from particleboard sides. Oldcastle’s Builder Select line used 5/8-inch particleboard rather than 3/4-inch plywood, so the screw threads strip out faster under load.
• Laminate countertops bubble or delaminate near seams. Hard water and heat cycling separate the laminate from the substrate. In Las Vegas, we see this first around the sink cutout where daily thermal shock hits hardest.
• Cabinet sides bow or shelves sag. The 58-pound density particleboard in economy lines absorbs moisture from steam and loses rigidity. Once the shelf pin holes elongate, the damage spreads.
• Finish peels or discolors in sun-exposed areas. Oldcastle’s thermofoil wraps can off-gas and separate when kitchen windows face south or west. We’ve replaced entire door sets in Aliante homes where afternoon sun cooked the vinyl.

Replacement Cost & What’s Included

What drives the range? Layout changes, electrical or plumbing relocations, and material grade. A straight cabinet swap with Oldcastle-compatible KraftMaid boxes runs toward the lower end. Moving walls, adding an island with plumbing, or upgrading to Cambria quartz pushes higher. Our quotes are upfront pricing, no surprises. Parts, labor, haul-away, and permit handling are itemized. Every kitchen remodel is backed by our 730-Day Done Right Promise. If it’s not done right, we make it right.

DIY or Call Us?

Here’s where we’re straight with you. Swapping a hinge or adjusting a drawer front? Most Las Vegas homeowners handle that with a screwdriver and patience. But cabinet installation involves structural load paths, level lines across uneven slab floors, and precise scribing to walls that aren’t plumb. We’ve walked into too many Centennial Hills kitchens where a DIY cabinet hang led to collapsed wall anchors or a countertop seam that cracked because the base wasn’t flat.

The real risk is the domino effect: a slightly off cabinet throws your countertop template, your backsplash line wanders, and your appliance panels don’t fit. Todd Mervyn grew up in Spring Valley watching his uncle frame additions, and the lesson stuck. Measure twice, anchor once, or call someone who’ll do it right the first time. For anything involving electrical relocation, gas line moves, or load-bearing wall changes, Nevada code requires licensed trades. We bring background-checked, uniformed technicians who handle the full scope from foundation to finish line.

Not sure where your job falls? Call (855) 951-4361. A live person answers 24/7, and estimates are free.

FAQs